Heating & Cooling
Everything else is correct as you describe it. Or is it more complicated than that? You will need to trace each of the thermostat wires down to see what each color wire controls.
- With this wiring configuration you are not going to have any heating because W would be the connection to turn the heat on.
- Honestly, I recommend that you call a professional to do this properly mainly for the humidifier problem.
- Oh, and check your main wiring schematic before hiring someone to hook up your thermostat.
- If Amazon doesn't like it, it kills the connection immediately.
- Additionally highlighting some of the differences in those functions from manufacturer to manufacturer.
- In other words, control board air handler that blue wire should be un-used the same as it is un-used at the sub-base.
Tom s Tek Stop
- The color might not be red, but maybe they, the installer, used another color for the hot wire.
- If you need more help after looking at the sticky, post back.
- It will capture the request from Amazon and then give it the reply Amazon is looking for.
- How do I connect my compressor now?
Green on the heat strip unit normally is the fan relay wire on the air handler and would attach to the G terminal on the thermostat. On a split system the blower fan is in the air handler. Would any other features like the two stage compressor that would be negatively affected? In either case, it is important to find the wiring diagram for the unit. You pair a name with a data type.
If it is loose in the air handler and not connected to anything then connect it to the common side of the transformer or terminal board in the air handler. At least now you understand how it works. There is a blue wire in the bundle. Electricity runs from the power wire to Common or neutral. Additional red and black wires were screwed into panel and plastic connector at other end plugged them into what looks like a motherboard.
Not sure without knowing what type of system you have. By using this form you agree with the storage and handling of your data by this website. Heating has a different control than the cooling in most systems and the reason is for humidity control. It was very interesting to read.
How to Hook Up a Home Thermostat
Always follow safety instructions especially with electricity. This is the wire you are looking for. Send a private message to letmetellu. Therefore, if you wire it wrong or accidentally touch the wrong wires together you can blow the low voltage transformer.
What else may I get that kind of info written in such a perfect approach? On the left side you should see Skills under Alarm. Special shielded wire is used for this run and completely separate form the other thermostat wires. Hi I bought a new smart thermostat and cant figure out the wiring as the letters are different and from what I read you cant trust the colors! For the thermostat wiring colors code for this terminal if equipped consult with the installer or trace the wire out to the source.
The white was connected to the yellow terminal. Seems to me not to be wired conventionally. You need the G terminal functionality for that.
Good Morning, I went in to the attic. Below we have a very informative Youtube Video made by grayfurnaceman which explains thermostat wire color codes. Ever seen anything like this? Or is it an an air conditioner with a gas furnace for heat? Obviously this wire is used to run the fan in air handler when the tstat is put in fan mode.
Your sample utterances doesn't include status or settings. If you want to include a description then do so here. My set up only has Yellow, Red, Green, Blue and white. See the menu on the right. Wrap it around the bundle and wire as instructed.
Hopefully my steps have been successful for you and you are now dangerous with the Amazon Echo. You can certainly do that. Getting skills to work with the echo is very frustrating. It is likely the orange wire but I have seen others use the blue wire in Rheem and Ruuds. If you are not comfortable doing this then I advise you call a professional.
I don t know how to hook up my new thermostat
Basic electrical safety and standards for wiring color The function of each wire terminal on the average thermostat. Breaker was off until the test phase. If I now hold contactor in, it powers on. There is also a good description of the thermostat wire colors and their function.
Many times the old duct work is still good it just needs to be resealed and re-insulated. No one knows until its gone through troubleshooting. Just share the site on social media ie Facebook, Twitter, Reddit and others. In my previous article I reviewed the Amazon Echo.
This is a layered control system where Honeywell controls some things while Trane controls other things. Just bought a Honeywell replacing the old Honeywell. The solution to your problem is to trace all the wires out to make sure they are terminated properly at the thermostat. Your thermostat does not have that terminal. But by creating our own Amazon Echo app, and using my previously discussed python script to control the thermostat, we can make it happen.
How do i hook up my thermostat - Warsaw Local
The blower motor does not seem to ramp down as I think it would with only one zone calling. This is how they should be connected. Attach that wire to the C terminal at both the new thermostat and the control board. If your still having problem.
Is it possible that the Black should be hooked up to the R? If the W wire is not hooked up to anything then you could use it for the C wire. How would you hook-up the following? From what I have read in the Honeywell installation guide.
In the meantime, I would recommend you call an authorized Trane dealer, questions to ask someone when ask them if they have technicians who are familiar with your type of system. They also have a proximity feature that works off the app on my phone. This is a red wire and comes from the transformer usually located in the air handler for split systems but you may find the transformer in the condensing unit.